Certainly, there are many types of air compressors in the market from which to choose. Some ideal for light duties others for heavy duties. However, not all air compressors available in the market are really good. If you want a resistant and durable machine, you must opt for the best brands.
Campbell Hausfeld is one of them. This company has more than 100 years of experience producing air compressors with the highest quality standards. Therefore, it’s one of the most popular brands in the world.
So, if you need to buy a new air compressor soon and you don’t know which model to choose, keep this well-known brand in mind before making any decision. In this article you’ll learn how to use a Campbell Hausfeld air compressor. You’ll also know a little more about the history of this well-known company.
What is Campbell Hausfeld Air Compressor?
Campbell Hausfeld has been producing air compressors for over 100 years. This company started in 1836, as a small farm equipment factory. More than a decade after its founding, the company bought an air compressor factory called Pressure King, owned by Joseph Hausfeld.
Since then, the company began to be called Campbell Hausfeld. Currently, its headquarters are located in Harrison, Ohio. It’s also one of the oldest and most powerful companies in the same state.
Today, this company produces more than air compressors. Its operations have diversified to produce other types of tools such as spray guns, electric welders, winches, generators and pressure washers.
Step by Step Guide to Use Campbell Hausfeld Air Compressor
Above all, Campbell Hausfell air compressors are powerful, durable and easy to use. However, before getting started, you need to know some basic things to get the most out of your pneumatic tool. Below, you’ll find several valuable tips for using your Campbell Hausfeld air compressor like a pro.
1. Wiring and Grounding
Campbell Hausfell can operate on a standard household 15amp electric circuit. The outlet must be grounded to allow current to escape in the event of a short circuit. You can adjust the power intake to work at 120V or 240V.
In addition, the engine has a built-in overload switch that turns off the engine in case of any possible overload.
2. Plugs and Receptacles
The outlet must have the same configuration as the power plug.
In the case of a Campbell Hausfeld 135 psi air compressor, any tube, pipe or hose connected to the device must have a pressure rate above 150 psi. Here’s a table with the recommended diameters according to the piping length:
|Piping Length||Diameter (inch)|
|Up to 50 ft||1/2|
|Greater than 50 ft||3/4|
Campbell Hausfeld air compressors require oil lubrication to prevent wear, and overheating and to reduce noise generation. When using the compressor for the first time, make sure that these elements are installed:
- Oil opening cap.
- Drain extension.
If both elements aren’t present on the device, remove the oil drain plug on the base on the pump and install the oil drain extension. Seal the extension with thread sealing tape to avoid oil leaks.
After that, remove the plastic plug on the oil opening and fill the compressor pump with oil. Then, check the oil side glass to make sure oil is filled up until the red dot. Finally, install the screw cap included in the product packaging on the oil opening.
The recommended lubricant for these devices is industrial SAE 30 oil. You can also use 10W 30 synthetic blend. Don’t use regular motor oil in these cases, because additives can generate waste that shortens the pump lifespan.
5. Start Up and Breaking
After completing the above steps, you’re ready to start up your air compressor. To do this, follow the steps below:
- First, run the air compressor continuously for 30 minutes to allow proper pressure of the piston rings.
- Then, fill the air pump with oil to the indicated level.
- After that, open the drain valve on the tank.
- Turn the regulator knob fully clockwise. Don’t connect any air hose on the air output at this point.
- Then, turn the pressure switch knob to “off” position.
- Plug in the power cord.
- After that, turn the pressure switch knob to “auto” position.
- Run the device during 30 minutes to break in pump parts.
- Finally, drain and replace oil after the first hour of runtime. This will maximize the lifespan of your air compressor.
To connect pneumatic tools and start using your air compressor, you must follow the steps below:
- First, turn the regulator knob clockwise to bleed off the air. Then, the compressor will restart at preset pressure.
- Then, turn the pressure knob to “off” position.
- Unplug the power cord.
- After that, turn the regulator knob fully clockwise to release all air pressure. Make sure the tank pressure reaches 0 psi.
- Attach the air hose to the air output of the pressure regulator.
- Then, attach the air tool to the other end of the air hose.
- Plug in the power cord.
- After that, turn the pressure knob to “auto” position.
- When reaching full pressure, turn the regulator knob clockwise until reaching the desired air output pressure.
- After using, turn the pressure knob to “off” position. Then, open the drain valve to release water from the tank. Finally, close the drain valve.
As you can see, using a Campbell Hausfeld air compressor isn’t difficult at all. You just need to carefully follow the instructions in this article. Thus, you’ll get the most out of your device and help extend its lifespan.
Remember that you can’t use regular motor lubricants on these devices. The additives can generate waste on the pump that can shorten its life. Make sure the outlets are grounded to prevent serious damage to the compressor in case of short circuit.